The E.H. Hotchkiss Company was started in 1897 when, several years after first investing in the company, Eli Hotchkiss gained control of the Jones Manufacturing Company. The Jones Manufacturing Company had been producing a stapling machine since 1895 known as the Star Paper Fastener. The Star Paper Fastener is the direct antecedent of the Hotchkiss No. 1. In 1901, after some design changes, the Star Paper Fastener was released as the Hotchkiss No. 1.
magazine ad from 1895
There were three different primary versions of the Hotchkiss No. 1 during the time it was available (see note 11). And each version came in two styles; with a staple-holding spiral coil (aka “tail”) and without.
The first version of the Hotchkiss No. 1 was introduced in 1898 and was available at least through 1921 and probably a bit longer. The picture above is of a first version without a spiral coil while the picture at the beginning of the post shows a first version with a spiral coil. A first version without a spiral coil weighed 1 pound 2 ounces and was made of nickel-plated cast iron. It measured 4″L x 2″W x 4.5″H.
newspaper ad from 1901
magazine ad from 1907
let’s call this version 2a
This version is something of a mystery. My initial reaction on seeing it is that it was a pre-production model or possibly a prototype. There are versions both with and without a spiral coil. Also, the model in the picture above has the NCR stamped plunger which implies it was available through them. However, I’ve never found any ads or catalog listings for this particular version. Further, the quality of the zinc used in the body was abysmal and it was coupled with a squared design that tended to cause stress cracks on different parts of the stapler body. My opinion is that this was the precursor to the version 2 (shown next) and that it had limited availability and was never advertised. As the version 2 below was advertised in 1920, again this is my opinion, I believe that this model was available about 1919. Note that the version 2 below has a more rounded front and this would have added greater strength compared to this version. (see note 12)
The second version of the No. 1 was introduced about 1920 and was available at least until 1921. It is possible that it was available a year or two before or after this time period but I cannot verify that at this time. However, it should be noted that due to the popularity and longevity of this stapler there was some overlap in the selling of the different versions of the No. 1 and it wasn’t unusual for stationer A to offer the first version for sale while stationer B offered the newer version. This weighed 1 pound 2 ounces and measured 3.875″ L x 1.938″ W x 4.438″ H. The body material was changed from iron to “nickel-plate diecast” metal. There were a number of improvements introduced with this version which was likely a response to the growing competition Hotchkiss had in the field of strip staplers. Observe also the design changes made to this version. It did keep the same style base, only enameled in black, the body shape changed slightly but most noticeably, again except for the base, all additional ornamentation has been removed for a much smoother and cleaner look. It is my belief that the introduction of the Greenfield Fastening Machine is the inspiration of both many of the mechanical improvements and also of the design changes.
magazine ad from 1920
magazine ad from 1921
The third version of the No. 1 was introduced in 1921. It was sold by stationers at least until 1946 but was likely available for a long-time afterwards. This weighed 1 pound 2 ounces and measured 3.875″ L x 1.938″ W x 4.188″ H. Also, while the plunger, anvil, and some of the internal parts were made of steel, the remainder of the stapler was made from “nickel-plate diecast”. Note the absence of details such as what type of diecast metal. All I can tell you is that the diecast is non-ferrous (not iron, steel, or any kind of magnetic metal). Again this model was introduced with some fanfare as an improved model which seemed to mainly consist of some kind of special staple straightener and guide which prevented clogs.
Models of the third version introduced between 1921 and 1924 had a base with the H logo pierced. It will also state Patent Pending. For third version models introduced after 1924 it will have a solid base and while the logo will be the same the base will not be pierced. These will also have a patent date along with the words “others pending”.
later version of Hotchkiss No 1 in black crackle finish available in 1940’s
magazine ad from 1921
magazine ad from 1922
The No. 1 was one of the first staplers to use a strip of staples. A staple-strip looks similar to today’s magazine staples. But whereas today’s staples are individual metal U-shaped fasteners individually manufactured and glued together into the strips you use currently, a staple-strip was actually formed and cut from a single piece of metal. When you pressed down on the plunger it cut the staple from the strip as opposed to simply separating it from the magazine strip. This necessitated a certain amount of force that today would be considered excessive. As a matter of fact, it was not unheard of when these were popular for office workers to have a rubber mallet nearby to use with this. That being said, my experience is that while these take more effort to use I’ve never had to resort to that kind of an extreme.
Hotchkiss No. 1 strip of staples
Staples for the Hotchkiss No. 1 are no longer made. However, if the mechanisms work then you can be confident that you have a working stapler. If you do find staples, I recommend caution in using them in your antique stapler. As I’ve mentioned before, old iron gets brittle and while you’ll probably be ok using your stapler once or twice it likely will not be able to stand up to regular use. Furthermore, unjamming one of these No. 1’s is extremely difficult to near impossible so if you do use it (even once) ensure that you use Hotchkiss staples. Other brands might have claimed to work in the No. 1 but keep in mind that items such as this were not made to the same exacting tolerances you’ve come to expect today so the likelihood of issues is greatly increased with off-brands.
The Hotchkiss No. 1 was sold for over 40 years making this probably the easiest antique stapler to find and add to your collection. It was successful enough to spawn a number of European manufactured clones and even gave its name to the Japanese language as the word for stapler (hotchikisu). And speaking of which…
I’ve recently come across another model of the Hotchkiss No 1. However, this model was only available in Japan. The bookkeeping supply catalog (note 7) that this picture is from was published in 1922 and you can certainly see elements of the third version No 1 in its design.
Patent & Other Information:
- Editors (1897, November). Trade Items. The American Stationer, page 734
- Reynolds Bros. (1901, July). advertisement. Scranton Tribune, page 5
- Editors (1903, October). The Story of the Man Who Made the Star Stapler Famous. The Book-Keeper The Business Man’s Magazine, pages 178-180
- F.P. Burnap Stationery and Printing Co Catalog (1915), Kansas City, MO page 111
- Hotchkiss Sales Co. (1920, December). advertisement. System the Magazine of Business, page 1121
- Editors (1921, November). New Member of the Hotchkiss Family. Walden’s Stationer and Printer, page 78
- Bunshodo Corporation catalog (1922, July), Tokyo, Japan page 45
- Editors (1922, September). Improvement of Hotchkiss Paper Fastener. The American Stationer and Office Outfitter, page 26
- Editors (1922, September). Hotchkiss Fasteners Now Have Straightener. Office Appliances, page 39
- The Brief Catalog (1938), Kansas City, MO page 17
- Utility Office Supply Catalog (1946), Chicago, IL page 387
- It had been brought to my attention that another collector was talking about a another version of the No 1 which I’ve labeled above as version 2a. He has stated that the reason it is so rare is that Hotchkiss was “embarrassed” by it. It is unlikely that it is so rare because Hotchkiss was embarrassed. More likely Hotchkiss took swift action to get these off of store shelves as soon as they discovered that it had some major quality shortcomings. Anyway, as soon as this heretofore unknown model was brought to my attention I started reaching out to fellow enthusiasts, antique shops, etc. in an effort to procure one of these. It took a bit over 6 months but I was able to find one, albeit in a pretty poor state, for under $30. For me, its real value is in how it fills in some blanks in the evolution of the No 1 Stapler. Information is practically non-existent for this model but I’ll stay the course looking for whatever I can find out.
- Below is a picture of a Hotchkiss No. 1A stapler (note the front of the base). This is a totally different stapler from the Hotchkiss No. 1. I’ve had more conversations with folks who thought I was talking about the below pictured stapler when in reality I was talking about the above models. You might be wondering why in the world didn’t they use a different numbering system for a different stapler. Unfortunately, the answer is; nobody knows.
Visit me at http://www.facebook.com/americanstationer.